考虑地表反射类型的气溶胶散射偏振特性

采用逐次阶散射法求解矢量辐射传输方程来研究气溶胶在不同地表反射模型下的散射偏振特性.首先,选取单一地表反射模型和耦合地表反射模型两种地表反射模型.然后,根据地表反射模型计算得到相应的地表反射率,进而采用逐次阶散射法对矢量辐射传输方程进行求解,得到散射光的Stokes矢量.最后,由Stokes矢量计算得出散射光的偏振度.仿真结果表明,两种地表反射模型下气溶胶单次散射的散射辐射强度和线偏振度均相等;耦合地表反射模型的总散射辐射强度和线偏振度总是大于单一地表反射模型;单一地表反射模型的气溶胶单次散射相对总散射的贡献总是大于耦合地表反射模型.研究结果对气溶胶光学特性的反演具有一定意义.     

基于Retinex理论与概率非局部均值的红外图像增强方法

针对传统红外图像增强算法中细节模糊及过度增强的问题,提出了一种基于Retinex理论与概率非局部均值相结合的红外图像增强方法.首先通过单尺度Retinex方法调整图像中过暗与过亮部分的灰度级;然后利用概率非局部均值对图像进行分解处理得到基本层与细节层,对基本层采用直方图均衡化拉伸对比度,对细节层采用非线性函数进行增强;最后,将不同层次的结果融合得到对比度与细节增强的红外图像.用该方法对多组不同场景的红外图像进行仿真实验,并将其与多种增强方法进行主、客观对比分析,结果表明所提方法在红外图像的细节及对比度增强方面都获得了更好的效果.     

氧化铟掺铪红外透明导电薄膜

采用射频磁控溅射与退火工艺相结合的方法,分别在石英和硒化锌(ZnSe)衬底上制备了掺铪氧化铟(IHfO)薄膜,掺杂比例In2O3∶HfO2为98wt.%∶2wt.%.测试了薄膜的组成结构和3～5μm红外波段的光电性质,分析了退火温度、薄膜厚度和氧气流速对薄膜性能的影响.X射线衍射、扫描电子显微镜和X射线能谱表明,制备的IHfO薄膜具有氧化铟的立方体结构,掺杂铪并没有影响氧化铟的生长方向,但是减小了晶格间距,铪与铟外层电子形成新的杂化轨道.傅里叶变换红外光谱表明,随着退火温度的增加,IHfO薄膜在3～5μm波段的透过率逐渐下降,沉积在ZnSe衬底上的薄膜具有更平稳的透过率,厚度为100nm薄膜在3～5μm波段平均透过率为68%.测试霍尔效应表明,随着氧气流速的增加,IHfO薄膜电阻率逐渐增加,载流子浓度减小,霍尔迁移率变化不明显.晶界散射是影响IHfO薄膜迁移率的主要因素,当氧气流速为0.3sccm时,薄膜最佳电阻率为3.3×10~(-2)Ω·cm.与透可见光波段的导电氧化铟锡(ITO)薄膜相比,制备的IHfO薄膜可以应用在3～5μm红外波段检测气体,红外制导等领域.     

均匀磁场下碳离子笔形束的剂量变化分析及位置修正方法

分析外加均匀磁场对于碳离子笔形束剂量分布的影响,并考虑修正这种影响,为磁共振成像引导碳离子放射治疗的临床应用提供指导。本文利用蒙特卡罗方法模拟计算了不同能量碳离子笔形束在不同强度磁场下的剂量分布情况,发现垂直于碳离子束入射方向的均匀磁场对于碳离子笔形束射程缩短的影响很小,磁场对碳离子束的主要影响是引起束流横向偏转,特别是碳离子束布拉格峰位置的横向侧移。横向侧移程度与碳离子束的能量和磁场强度相关,根据模拟结果,得到了一个计算碳离子束布拉格峰在磁场中相对横向偏转的方程,并提出一种校正外加磁场引起的碳离子束布拉格峰横移的角度修正方法。这些结果可用于指导磁共振图像引导碳离子放射治疗计划系统的研发。     

基于近似解析法的超导储能磁体设计

降低超导储能磁体的研制成本一直是控制超导磁储能系统(Superconducting Magnetic Energy Storage, SMES) 总成本的重要手段之一. 本文考虑在一定磁体结构参数范围内, 磁体产生的最大磁场值可以采用级数进行 表示, 磁体的电感值可以采用线性函数表示, 给出了超导储能磁体磁场能量的近似解析表达式, 提出了一种基于近 似解析法的超导储能磁体设计方法. 该方法以储能磁体的线材用量最小作为设计目标, 在给定超导线材参数和临界电流特性曲线, 以及磁体储能总量要求的情况下, 依据此方法可快速的得到成本最优时所对应的磁体结构参数.将近似解析法优化和采用传统的有限元软件 Ansys 仿真优化进行对比分析, 结果表明采用近似解析法进行磁体优化更加方便快捷, 节省了大量计算时间.     

新型非对称二苯并[b,f][1,5]二氮杂环辛四烯的合成

以两种不同取代的2-氨基二苯甲酮为原料,氯苯为溶剂,BF3-Et2O为脱水剂,通过分子间脱水一步环化缩合制备非对称二苯并[b,f][1,5]二氮杂环辛四烯衍生物。运用HPLC监控反应过程,优化合成工艺,得到最佳反应条件为:等物质的量的两种不同取代2-氨基二苯甲酮和BF3-Et2O,在氯苯中回流反应12 h。化合物4a^4c为新化合物,其结构经1H NMR,13C NMR和MS(ESI)表征。     

Measured and Predicted Solubility Phase Diagrams of Quaternary Systems LiBr-NaBr-MgBr2-H2O and LiBr-KBr-MgBr2-H2O at 298.15 K

The stable phase equilibria of quaternary systems LiBr-NaBr-MgBr₂-H₂O and LiBr-KBr-MgBr₂-H₂O at 298.15 K were studied by both experimental measurement(isothermal solution saturation method) and theoretical prediction(Pitzer model). The solubilities of the saturated solution have been determined experimentally and two stable phase diagrams and relevant water diagrams of the two quaternary systems were obtained. Results show that quaternary system LiBr-NaBr-MgBr₂-H₂O is hydrate II type as NaBr and NaBr·2H₂O coexistence. Its phase diagram consists of only one invariant point, four univariant curves, and five crystallization fields. The quaternary system LiBr-KBr-MgBr₂-H₂O is a complex type as the double salt KBr·MgBr₂·6H₂O formed. In addition to this double salt, the three single salts LiBr·2H₂O, KBr and MgBr₂·6H₂O also crystallize. In this paper, the solubilities of phase equilibria in above quaternary systems were also calculated by the Pitzer's electrolyte solution model. All the needed parameters can be obtained from the literature or be fitted by experimental data. On the Basis of the experimental and calculated results, the phase diagram of the quaternary system was plotted for comparison. It shows that the calculation results are consistent with the experimental ones.     

Effect of Support on Catalytic Performance of Photothermal Fischer-Tropsch Synthesis to Produce Lower Olefins over Fe5C2-based Catalysts

Photothermal Fischer-Tropsch synthesis(FTS) has been extensively studied, but few reports were focused on systematically exploring the influence of support on catalytic performance. Herein, a series of Fe₅C₂-based catalysts with different supports was fabricated via a one-step wet-chemical method for photothermal conversion of syngas to lower olefins. Under light irradiation, the optimized Fe₅C₂/α-Al₂O₃ catalyst demonstrated remarkable photothermal FTS activity, delivering selectivity to lower olefins of 50.3% with a CO conversion rate of 52.5%. Characterization studies using X-ray diffraction and Mössbauer spectroscopy analysis revealed that the active catalyst mainly contained Fe₅C₂ nanoparticles on α-Al₂O₃ support. It was found that the weak interaction between active phase and α-Al₂O₃ could promote the formation of Fe₅C₂, which contributed to the high selectivity to lower olefins.